OSD Audio IWS-88 Bedienungsanleitung

OSD Audio Subwoofer IWS-88

Lies die bedienungsanleitung für OSD Audio IWS-88 (2 Seiten) kostenlos online; sie gehört zur Kategorie Subwoofer. Dieses Handbuch wurde von 25 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 13 Bewertungen. Hast du eine Frage zu OSD Audio IWS-88 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/2

18AWG minimum - for distances up to ………………………. . 10 ft

16AWG - from ……………………………………………. 10 to 50 ft

14AWG - from …………………………………………… 50 to 100ft

- Where is the best place to install the speakers

- Where do the speakers sound the best

- When placing the speakers in the wall, try to locate them so that the

sound is projected towards the general listening area.

- If you intend to paint the grilles, try to do so before installation.

Quick installation guide

- Pencil

- Drill

- Tape Measure

- Wire cutter

- Philips-head screwdriver

- Sandpaper

Tools needed for installation

STEP 1

Trace along the inclusive template. Cut along the traced line using a

drywall saw or rotary drill. A simple, inexpensive drywall saw (about

$10 at your local hardware store) is the best choice for beginners.

Caution: This is the most important part of the entire installation.

If you are not certain whether any obstructions exist behind the

desired mounting area, you should start by cutting a small hole in

the center of your penciled mounting hole with a drywall saw. Use a

piece of sandpaper to sand down the cut out edge for a smoother

contour. (See Diagram 1 and Diagram 2)

Run the cable into the cut out location while leaving an extra two

feet to make the connection to the speaker easier. St

STEP 2

rip back

approximately ½” of the speaker cable insulation and twist

the copper wires tightly for easy insertion.

On the back of the speaker, press down on the gold-plated

compression terminal to reveal the "eye" and insert the speaker

cable through the eye for secure connection. Release the compres-

sion terminal to lock each cable securely.

Diagram 1:

Cutout tracing

Diagram 2:

Cut Out

To determine the length and the gauge of speaker wire, you will need to

measure the distance between your receiver/amplifier and the speakers.

- Always buy more than you think you would need.

- Equal wire lengths should always be used to maintain an equal

balance in sound volume.

- Sound quality is lost when using thin wire gauge over a long

distance.

- Utility knife

- Safety eyewear

- Gloves

Speaker wire

- -

- Measure the distance from the receiver/amplifier to the speakers.

-----------------

----------------

-----------------

----------------

-----------------

STEP 3

Tighten the dog-ear brackets by simply turning the screws on the

slowly clockwise. The quick-turn mounting system and frame will

"sandwich" or clamp around the wall to hold the speaker securely in

place. (See Diagram 3)

Diagram 3:

Mounting Dog Ear

Closed

Loose

Closed

oose

..... ......

......

dog ear

STEP 4

Screw

Tighten the four mounting screws with the same amount of force until

the speaker is aligned and held securely to the wall surface. Caution:

do not over tighten! (See Diagram 4)

Diagram 4:

MANUAL

DUAL 8" IN-WALL

S U B W O O F E R

IWS88

Produktspezifikationen

Marke:	OSD Audio
Kategorie:	Subwoofer
Modell:	IWS-88
Breite:	290.5 mm
Tiefe:	101.6 mm
Gewicht:	- g
Empfohlene Nutzung:	Universal
Produktfarbe:	Black, White
Übertragungstechnik:	Kabelgebunden
Impedanz:	8 Ohm
Höhe:	479.4 mm
RMS-Leistung:	240 W
Schnellstartübersicht:	Ja
Betriebsanleitung:	Ja
Audio Kanäle:	2.0 Kanäle
Frequenzbereich:	45 - 500 Hz
Woofer:	Ja
Tieftönerdurchmesser (imperial):	8 "
Hochtöner:	Nein
Lautsprecherplatzierung:	Ceiling-mountable, In-wall/in-ceiling
Anzahl der Hochtöner-Antriebe:	1
Anzahl der Tieftöner-Antriebe:	1
Verstärker:	Nein
Empfindlichkeit:	90 dB
AirPlay:	Nein
Für die Nutzung im Außenbereich geeignet:	Ja
Tieftönerdurchmesser:	203.2 mm
Multi-Room Streaming (MRS) Unterstützung:	Nein