Rane SSE 35 Bedienungsanleitung
Rane
Nicht kategorisiert
SSE 35
Lies die bedienungsanleitung für Rane SSE 35 (8 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Rane SSE 35 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/8
Manual-1
OPERATORS MANUAL SSE 35
HOME CINEMA EQUALIZER
QUICK START
Great video is ready-made; great audio is harder to get, but a SSE 35 makes it a lot easier. Read at least this boxed
section and you’ll be on your way toward great audio.
Hook-up is intuitive: In from the decoder; Out to the amplifiers. Just follow the silkscreened legends on the rear of the
unit. Use only high-quality RCA cables.
Set your Dolby Pro-Logic decoder's center channel to NORMAL Mode.
Familiarity with any other graphic equalizer makes you familiar with the SSE 35. If this is your first equalizer, be
gentle; it can overwhelm you. Use of a realtime analyzer is recommended; alternatively use an SPL meter and a test disc—
then try your ears.
Use the BYPASS switch as an aid in comparing equalized results with unequalized results. Pushbutton in and locked
(LED on) is the bypassed (unequalized) mode; pushbutton out and unlocked (LED off) is the normal equalized mode. See
the included Rane Note 132 for stereo or mono subwoofer tips. See the Operating Instructions on the back page for basic
alignment info.
Install the supplied security cover after completing all settings. Be sure the POWER light fits snugly into the hole in the
security cover.
NEVER CONNECT ANYTHING EXCEPT AN APPROVED RANE POWER SUPPLY TO THE RED MODU-
LAR JACK ON THE REAR OF THE UNIT. This is an AC input and requires a power supply exactly like the one
originally packed with your unit. See the full explanation of the power supply requirements elsewhere in this manual.
Have fun.
Manual-2
FRONT PANEL DESCRIPTION
1. LEFT, RIGHT & CENTER CHANNEL equalizer controls. Each of the Left, Right and Center Channels have eleven
slide controls used to set the individual levels of the 2/3-octave spaced (160 Hz-16 kHz) constant-Q filters. Their range is
±6 dB. The grounded center-detent design ensures each filter is off when positioned to 0 dB. Each center frequency is
clearly labeled above the respective slide control.
2. LEFT & RIGHT SUBWOOFER/low frequency equalizer controls. Each of the Left & Right Subwoofer Channels (or the
L&R Front Low Frequency Bands if no subwoofer) have seven slide controls used to set the individual levels of the 1/3
octave spaced (25 Hz-100 Hz) constant-Q filters. Their range is ±6 dB. As above, the grounded center-detent design ensures
each filter is off when positioned to 0 dB. Each center frequency is clearly labeled above the respective slide control.
3. POWER indicator. This blue LED lights any time remote power is supplied from the Rane model RS 1 power supply
(included). To avoid confusion a distinction is made here between electrical and political power.
4. BYPASS switch & indicator. This pushbutton switch activates the relay-controlled BYPASS function. Engaging the
BYPASS switch (red BYPASS LED on) ties the INPUT connectors directly to their respective OUTPUT connectors (hard-
wired). This switch is particularly useful in performing “A/B” comparisons between equalized and non-equalized sound.
This switch does not bypass the subwoofer crossovers, only the equalizer sections. Use generously during set-up. During
the initial timed power-up sequence, the SSE 35 automatically goes into BYPASS mode.
Manual-3
REAR PANEL DESCRIPTION
1. Remote POWER supply input. The unit is supplied from the factory with a Model RS 1 Remote Power Supply suitable for
connection to this input jack. The power requirements of this unit call for an 18 volt AC center-tapped transformer only.
THIS IS NOT A TELEPHONE JACK. NEVER USE A POWER SUPPLY OTHER THAN THE ONE SUPPLIED OR A
REPLACEMENT APPROVED BY RANE CORPORATION. Using any other type of supply may damage the unit and void
the warranty.
2. Ground LIFT switch. This switch provides the ability to separate chassis ground and signal ground. Normally, this switch
should be in the LIFT position. In some circumstances, moving this switch eliminates hum problems. Always turn your
amplifier levels down before changing this switch and bring them up slowly.
3. Chassis ground. A 6-32 screw used for chassis grounding purposes. See CHASSIS GROUNDING below.
4. LEFT, CENTER & RIGHT OUTPUT connectors. Active unbalanced design. Use only high-grade RCA cables for
connection to the power amplifier inputs.
5. LEFT, CENTER & RIGHT INPUT connectors. Active unbalanced design. Use only high-grade RCA cables for connec-
tion to the surround sound decoder outputs.
6. SUBWOOFER OUTPUT connector. Active unbalanced design. Use only high-grade RCA cables for connection to the
subwoofer power amplifier input.
7. SUBWOOFER ENGAGE switches. Pressing both of these switches to the in position and illuminating the red LEDs
engages the crossovers and routes the low frequencies to the SUBWOOFER OUTPUTS.
8. SUB SOURCE switches. These switches determine if the SUBWOOFER OUTPUT for each Channel gets its input from the
Left, Right, or a summed Left/Right signal. Set these to LEFT and RIGHT for stereo subwoofers, and L&R when using a
mono subwoofer.
9. CROSSOVER FREQUENCY switches. One each for Left and Right Channels. This sets the built-in 24 dB per octave
crossover to only allow frequencies below 80 Hz or 125 Hz to the subwoofer(s) in each Channel, thereby improving
subwoofer efficiency. If the subwoofer has a crossover frequency ajustment, set it to its highest value when using the SSE
35. Refer to the OPERATING INSTRUCTIONS on page Manual-6.
CHASSIS GROUNDING
If after hooking up your system it exhibits excessive hum or buzzing, there is an incompatibility in the grounding
configuration between units somewhere.
Units with outboard power supplies do NOT ground the chassis through the line cord. Make sure that these units are
grounded either to another chassis which is earth grounded, or directly to the grounding screw on an AC outlet cover by
means of a wire connected to a screw on the chassis with a star washer to guarantee proper contact.
Please refer to RaneNote 110 “Sound System Incterconnection” (supplied in this manual) for further information on
system grounding.
Produktspezifikationen
| Marke: | Rane |
| Kategorie: | Nicht kategorisiert |
| Modell: | SSE 35 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Rane SSE 35 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Rane
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
Bedienungsanleitung Nicht kategorisiert
- Vivanco
- Berkel
- Delta Dore
- Imperial
- DreamGEAR
- KanexPro
- Fujifilm
- Sanwa
- Hecate
- VOREL
- Hasselblad
- Homedics
- Vello
- Brainstorm
- LifeStraw
Neueste Bedienungsanleitung für -Kategorien-
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025