WAC Lighting HR-8401E Bedienungsanleitung
WAC Lighting
Nicht kategorisiert
HR-8401E
Lies die bedienungsanleitung für WAC Lighting HR-8401E (1 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 5 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 3 Bewertungen. Hast du eine Frage zu WAC Lighting HR-8401E oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/1
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JUNE, 2014
INSTALLATION INSTRUCTION
4” Low Voltage - Non-IC Remodel - Electronic
HR-8401E
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting o the electricity.
• Read all instructions before installing.
• For installation by a qualied electrician.
• System is intended for installation in accordance with National Electric Code, and local regulations.
Consult with local inspector to assure compliance.
• To reduce the risk of re, electrical shock and injuries to persons, turn o power at main switch before installing
or modifying the system.
• Warning: (Risk of re) do not install insulation within 3 inches of xture sides, or junction box, or in a manner to entrap heat.
• Retain instructions for future maintenance reference.
OVERVIEW
Housing is non-insulation contact, remodeling type, and 50 watts maximum.
Housing requires a trim from the HR-D8400 series, and lamp to be
complete (ordered separately Maximum wattage is determined by trim style.
If dimming, will generally work with standard incandescent dimmers,
or electronic type dimmers.
CUT OUT:
1. Use the template (supplied) to make a 4 3/8”
cut out hole in the existing ceiling.
2. Pull ceiling wire through the hole.
WIRING:
1. Junction box is suitable for chain wiring of multiple xtures
and is supplied with a spring latch door, and two trade size
knockouts for BX or Romex® connectors.
2. Remove junction box door and connect xture wires to
building wires: Green ground wire to bare copper or green
building wire, white xture wire to white neutral wire,
black xture wire to (hot) black wire.
3. Secure with wire nuts (supplied).
4. Replace junction box door.
MOUNTING:
1. Pivot the J box up through the hole, followed by the can.
2. Hold the rim snug to the ceiling surface.
3. From inside the housing push and pivot the housing clips
so they make contact with the top of the ceiling
Note: 3/4 inch maximum ceiling thickness.
FINISHING:
1. Socket wire is sucient in length to be attached to
the pins of the lamp before it is inserted.
2. Push the trim assembly up until the trim ring is ush to the ceiling.
Produktspezifikationen
| Marke: | WAC Lighting |
| Kategorie: | Nicht kategorisiert |
| Modell: | HR-8401E |
Brauchst du Hilfe?
Wenn Sie Hilfe mit WAC Lighting HR-8401E benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert WAC Lighting
20 Januar 2026
20 Januar 2026
20 Januar 2026
19 Januar 2026
19 Januar 2026
19 Januar 2026
19 Januar 2026
18 Januar 2026
18 Januar 2026
17 Januar 2026
Bedienungsanleitung Nicht kategorisiert
- Cimco
- KJB Security Products
- Ardes
- LinkedPRO
- Oasis
- Envertec
- BendixKing
- Medel
- Audiotec Fischer
- ESI
- VALOI
- Turbo Scrub
- DK2 Power
- EWT
- Vortex
Neueste Bedienungsanleitung für -Kategorien-
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026