Zenec ZE-RCE3704-2S Bedienungsanleitung

Lies die bedienungsanleitung für Zenec ZE-RCE3704-2S (4 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 7 Bewertungen. Hast du eine Frage zu Zenec ZE-RCE3704-2S oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

ZE-RCE3704-2SZE-RCE3704-2S

MOUNTING INSTRUCTIONSREAR VIEW CAMERA FOR FIAT DUCATO

ZE-RCE3704-2SZE-RCE3704-2S

REAR VIEW CAMERA FOR FIAT DUCATO

CAUTION:

Use the included connection cable exclusively. Altering or replacing it will void your warranty.

The camera is water- and dustproof and has been licensed according to the international standard IP68. However, vehicle clean-

ing using high pressure water and steam jet devices may still lead to damage of IP68 rated camera models by water intrusion.

Keep a distance of at least one meter between the water nozzle and the camera housing.

KEY FEATURES

• Compact high resolution rear view camera for FIAT Ducato III

vehicles, incl. Series 8 and other identical type variants

• System design integrating the original Ducato brake light

retaining the road use homologation*

1

• Cam1 sensor with 50° and Cam2 sensor with 100° horizontal

view angle

• Manual adjustment of vertical image section of Cam2

• IR-LED illumination system with dynamic LDR brightness

control for Cam2

• Integrated microphone (Cam2)

• Separable main cable with DOMETIC CAM035 6-pin

connectors, suitable for direct connection with factory routed

DOMETIC main cable in vehicle

• Plastic injection main housing with stainless steel fi xation bolts

*

1

The ZE-RCE3704-2S integrates into the original brake light insert of the vehicle.

The brake light is not part of the supplied set content.

9. Cam2 pointing down is a vertically swiveling design,

allowing to align the desired image section shown on the

HU manually. Align cam2 for best field of view. Installation

and cam setup is completed.

1. Unscrew and remove both Philips head screws.

Retain the screws for later remounting of the brake light

reflector.

1

2. Pull the brake light reflector unit out of its mounting

slot. Disconnect the white power supply system

connector plug of the vehicle.

2

3. Screw in and tighten the stainless steel mounting

bolts by hand (5Nm). Use a dab of Loctite, if possible.

3

4. Route the main cable from the naviceiver in the vehicle

cockpit / dashboard to the brake light opening in the up-

per rear section of the vehicle. For power and RCA video

signal, the ZENEC Infotainer offers a direct system “con-

nector block E” which offers switched 300mA power out’s

(see installation guide of ZENEC head unit).

5. Connect the 6PIN connector plug of the cam sensor

side with its counterpart of the cable coming from the

vehicle. Use self-adhesive tape to physically secure the

connectors as well as to prevent water from entering the

connectors.

5

6. Plug in the white power supply system connector

plug in the socket of the brake light reflector housing

backside.

6

7. Align the cam housing / reflector assembly over the

mounting location. Fix the assembly with the original

Philips head screws.

7

8. (no picture)

Connect the wires and connectors of the cam main har-

ness to the HU in the dashboard. Perform a cam function

test. Also check for proper function of the 3

rd

brake light.

Reverse

Speed In

IR In

ext. Mic

Power 2 300mA

Power 1 300mA

MIC

CAM 2

CAM 1

E

4

INSTALLATION

30 cm

3.5 mm

jack

11.0 m

9

COMPATIBLE WITHMODEL TYPEMODEL YEAR

Fiat Ducato III250/2512006 – 2011

Fiat Ducato III250/2512011 – 2014

Fiat Ducato III250/251 (X290)2014 – 2021

Fiat Ducato IIISeries 8as of 2021

Citroën Jumper II 250/250D/250L as of 2006

Peugeot Boxer 250/251as of 2006

Opel MovanoType Cas of 2021

ZE-RCE3704-2S

CAM 1 & 2CAM 1 & 2

Fuse

Fuse

Male

Female

white

yellow

red

white

black

red

MIC

CAM 2

CAM 1

+12V

CAM1

+12V

CAM2

GND

Male

Female

Dometic 6 pinDometic 6 pinDometic 6 pinDometic 6 pin

11 m

100 mm

300 mm

150 mm

200 mm

1

2

3

6

5

4

1

2

3

6

5

4

+12 V CAM 2

CAM 1 signal +

MIC signal +

+12 V CAM 1

GND

CAM 2 signal +

white

yellow RCA

red RCA

red

black

white RCA

Original Connection

1

2

3

6

5

4

MALEFEMALE

Pin out of WAECO/DOMETIC 6 pin connectors

WIRING DIAGRAM

ZE-RCE3704-2S

1

2

3

6

5

4

1

2

3

6

5

4

+12 V CAM 2

CAM 1 signal +

MIC signal +

+12 V CAM 1

GND

CAM 2 signal +

red

yellow RCA

red RCA

white

black

white RCA

Original Connection

1

2

3

6

5

4

MALEFEMALE

ZE-RCE3704-2S

Fuse

Fuse

Male

Female

white

yellow

red

white

black

red

MIC

CAM 2

CAM 1

+12 V

CAM 2

+12 V

CAM 1

GND

Dometic CAM035 6 pinDometic CAM035 6 pinDometic CAM035 6 pinDometic CAM035 6 pin

11 m

ZE-RCE3704-2S Wiring Diagram

Pin out of DOMETIC CAM035 6 pin connectors

100 mm

300 mm

150 mm

200 mm

Male

Female

1

2

3

6

5

4

1

2

3

6

5

4

+12 V CAM 2

CAM 1 signal +

MIC signal +

+12 V CAM 1

GND

CAM 2 signal +

red

yellow RCA

red RCA

white

black

white RCA

Original Connection

1

2

3

6

5

4

MALEFEMALE

ZE-RCE3704-2S

Fuse

Fuse

Male

Female

white

yellow

red

white

black

red

MIC

CAM 2

CAM 1

+12V

CAM2

+12V

CAM1

GND

Dometic CAM035 6 pinDometic CAM035 6 pinDometic CAM035 6 pinDometic CAM035 6 pin

11 m

ZE-RCE3704-2S Wiring Diagram

Pin out of DOMETIC CAM035 6 pin connectors

100 mm

300 mm

150 mm

200 mm

Male

Female

TECHNICAL SPECIFICATIONS

Image device Cam1 / Cam2: Pixelplus PC3089

Image sensor type: 1/3“ / 8.5 mm CMOS sensor

TV system: NTSC / 60 fps

View angle Cam1 / Cam2: 50° / 100° horizontal

Total sensor-die based pixel matrix: 756 (H) x 504 (V) pixels

Image relevant pixel matrix: 720 (H) x 480 (V) pixels

Lens focal length: f4.2 / f2.0

Frame rate: 60 fi elds/sec.

Signal to noise ratio: >47 dB

Dynamic contrast: >62 dB

Light sensitivity: 0.5 Lux/F1.2/50IRE – 0 Lux with

IR-LED ON

Video output: 1.0 ±0.2 Vp-p, 75 Ω, CVBS

White balance: Auto

Backlight compensation: Auto

Gamma correction: 0.45

Gain control: Auto

Sync system: Auto

Power supply: 12 DCV (6 V – 16 V)

Current consumption (@12 V DC): 80 mA ±10 mA total for

Cam1 + Cam2

IP protection rating: IP68

Operating temperature: -20° C ~ +70° C

ZENEC by ACR AG ∙ Bohrturmweg 1 ∙ CH-5330 Bad Zurzach ∙ Switzerland,

EU Legal Representative:

ACR S & V GmbH∙Industriestr. 35∙D-79787 Lauchringen∙ Germany ∙ www.zenec.com

Rev.B

Produktspezifikationen