Zenec ZE-RVSC200-MK2 Bedienungsanleitung

Lies die bedienungsanleitung für Zenec ZE-RVSC200-MK2 (4 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 5 Bewertungen. Hast du eine Frage zu Zenec ZE-RVSC200-MK2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

ZE-RVSC200-MK2

ZE-RVSC200-MK2

MOUNTING INSTRUCTIONSTWIN-SENSOR REAR VIEW CAMERA

KEY FEATURES

• Compact twin-sensor rear view camera

• Fast-mount click-on system for camera main assembly on mounting plate

• Cam1 sensor with 50° and Cam2 sensor with 95° horizontal view angle

• Manual adjustment of vertical / horizontal image section for Cam1 /

Cam2

• IR-LED night-illumination system for Cam2 with dynamic LDR brightness

control

• Integrated microphone (Cam2)

• Separable 3-part system cable with 17.0 m main cable length

• Adaptor for factory-installed Waeco main cable supplied with the set

DESCRIPTION

The ZENEC ZE-RVSC200-MK2 twin-lens rear view camera was specially

developed for semi- and fully-integrated motorhomes. In the upper part of

the camera body is the so-called Cam1. The main task of this camera is to

replace the not available interior mirror. The camera lens, which is located

in the lower part, is called Cam2 and is mainly intended for maneuvering

and reversing. Cam2 will record the individually adjustable area of up to 5

meters behind the motorhome. An integrated microphone as well as the IR-

LED night illumination system will support the lower camera (Cam2).

This product is compatible with a variety of 2-DIN A/V aftermarket

receivers and models of the ZENEC E>GO line up, featuring two inputs for

reversing cameras and one for microphone.

CAUTION:

■ Use the included connection cable exclusively. Modifying the cable will void your warranty.

■ The camera is water- and dustproof and has been licensed according to the international standard IP69K. However, vehicle cleaning using

high pressure water and steam jet devices may still lead to damage of IP69K rated camera models by intrusion of water.

■ If the vehicle is treated with a water jet high pressure cleaning device, make sure to keep a distance of at least one meter between the water

nozzle and the camera sensor / housing.

Ø 10 mm

Ø 2.5 mm

Ø 2.5 mm

Find a suitable spot for the camera on the back of your motorhome. The optimum height is about

2.5 m from the ground.

Take the mounting plate, hold it into the desired position and mark the midpoints of the five holes

as shown on the left. Remove the mounting plate and drill one hole with a diameter of Ø 10 mm

through the middle cross (cable port) and four holes with a Ø 2.5 mm through the corner crosses.

Hold the mounting plate in place and screw it with the provided tapping screws to the motorhome.

Pass the two cables through the middle hole and seal it with either vehicle glue or similar sealant.

Finally, all you have to do is click on the camera main assembly on the mounting plate, route the

cable to the radio bay and adjust both cameras manually.

Technical Specifications:

Image device Cam1/Cam2:

6.09 mm SONY IMX225LQR CMOS

sensor

Lens focal length Cam1/Cam2: f3.5 / f2.3

TV system: NTSC / 30 fps

View angle CAM1/Cam2:

90°(D)x50°(H)x45°(V) / 130°(D)x95°(H)

x75°(V)

Native sensor resolution:1305 (H) x 977 (V) pixels

Resolution of video-out: > 420 TV lines

Frame rate: 30 fi elds/sec.

Signal to noise ratio: > 48 dB

Light sensitivity: 0.3 Lux

Video output: 1.0 Vp-p, 75 ohms CVBS

White balance: Auto

Backlight compensation: Auto

Gamma correction: 0.45

Gain control: Auto

Sync system: Auto

Power supply: DC 12 V

Current consumption Cam1/

Cam2:

70 mA / 100 mA @12VDC, ≤ 2040 mW

IP protection rating: IP69K

Operating temperature: -30° C ~ +75°C, RH 95 % max.

Audio Out (Cam 2)

Video Out (Cam 2)

Video Out (Cam 1)

Camera 1 Power (+12V)

Ground (GND)

Camera 2 Power (+12V)

17 m

0.4 m

0.4 m

White

Black

Red

ZENEC by ACR AG ∙ Bohrturmweg 1 ∙ CH-5330 Bad Zurzach ∙Switzerland,

EU Legal Representative:

ACR S & V GmbH∙Industriestr. 35∙D-79787 Lauchringen∙Germany www.zenec.com

Rev. A

MADE IN TAIWAN

Produktspezifikationen