NightStick TWM-352 Bedienungsanleitung

Lies die bedienungsanleitung für NightStick TWM-352 (8 Seiten) kostenlos online; sie gehört zur Kategorie Beleuchtung. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 9 Bewertungen. Hast du eine Frage zu NightStick TWM-352 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com

INS-TWM-352-20

WARNING: IT IS IMPERATIVE THAT SAFETY MEASURES BE EMPLOYED AT

ALL TIMES WHILE HANDLING A FIREARM.

WATCH COMPLETE INSTALLATION VIDEO AT: http://bit.ly/2oN4VXC

INSTALL BATTERIES

Image 1

Image 2

Image 3

yOpen the Battery Door Screw using a Phillips head screwdriver. (Image 1)

yInsert the included CR-123 Batteries using the battery orientation markings on

the side of the light. (Image 2)

yRe-install the Battery Door Screw until fully tightened. (Image 3)

INSTALL THE TWM ON TO YOUR FIREARM

Your TWM comes with both cross rail inserts pre-installed in cross rail slots 1 & 4.

yIf the location of one or both of these is not correct for your speci c installation,

remove either or both of the inserts and then proceed to step 1.

yIf the location of the pre-installed inserts is correct for your  rearm, proceed

to step 3.

WARNING: DO NOT INSTALL THE TWM ONTO A FIREARM WITHOUT

USING THE CROSS RAIL INSERT. FAILURE TO USE A CROSS RAIL INSERT

COULD RESULT IN THE TWM COMING LOOSE FROM THE FIREARM

UNDER EVEN NORMAL RECOIL.

STEP 1: DETERMINE WHICH CROSS RAIL INSERT SLOT TO USE

Image 4Image 5Image 6

yHold the TWM alongside the Picatinny rail on your  rearm and determine which

of the 4 Cross Rail Insert Slots milled into the top of the TWM is best suited for

your  rearm. (Image 4)

yA single Cross Rail Insert can be installed in any of the 4 Cross Rail Insert Slots

milled into the top of the TWM.

ySlots 1, 3 & 4 (Image 5) are set up at a standard 1913 spacing, meaning that

all 3 will line up with a Mil-STD-1913 Picatinny Rail. If the desired installation

location on your  rearm will allow it, both of the 2 included Cross Rail Inserts may

be installed in any combination of slots 1, 3 or 4. Using both of the Cross Rail

Inserts will increase the retention of the TWM onto the Picatinny rail.

STEP 2: INSTALL THE CROSS RAIL INSERT INTO THE TWM

yLine up the Insert into the correct slot and make sure it is fully seated into the

slot.

yUsing the 2 Cross Rail Insert Cap Head Screws and the supplied Allen Wrench,

begin installing the Cap Head Screws.

yIf installing a second insert, repeat the  rst two steps using the additional insert.

yFully tighten all Cap Head Screws using the long side of the Allen Wrench.

(Image 6)

NOTE: The Allen Wrench should  ex a very small amount when the Cap Head

Screws have been tightened correctly.

WARNING: NIGHTSTICK STRONGLY RECOMMENDS PERIODICALLY

CHECKING TO INSURE THAT THE CROSS RAIL INSERT SCREWS REMAIN

TIGHTENED. FAILURE TO KEEP THESE SCREWS TIGHT CAN RESULT IN

DAMAGE TO THE TWM AND/OR THE CROSS RAIL INSERTS UNDER RECOIL.

Instruction Manual

TWM-352

Please read these instructions before using your Nightstick TWM-352.

They include important assembly and operating instructions.

PACKAGE CONTENTS

y1 - Weapon Mounted Light – Long Gun Single Switch

y2 - CR-123 Lithium Batteries

y1 - Set of Cross Rail Inserts (pre-installed)

y4 - Cross Rail Mounting Cap Head Screws (pre-installed)

y1 - Allen Wrench

WEAPON SAFETY

PLEASE BE SURE TO READ, UNDERSTAND AND FOLLOW THESE SAFETY

AND OPERATING INSTRUCTIONS WHEN HANDLING A FIREARM OR THE

NIGHTSTICK TWM WHEN MOUNTED ON A FIREARM. FAILURE TO DO SO

CAN BE DANGEROUS AND COULD RESULT IN SERIOUS INJURY, DAMAGE

TO PROPERTY, OR DEATH.

Use of a  rearm under any circumstance is inherently dangerous. SERIOUS

INJURY OR EVEN DEATH may result without proper training in the safe handling

of  rearms. Proper training should be obtained from an accredited  rearms safety

program conducted by a quali ed instructor.

Read, understand and follow all of the safety instructions that came with your

 rearm before attaching your new TWM.

yAlways assume every  rearm is loaded and treat that  rearm as such.

yNever point a  rearm at anything that you are not willing to destroy.

yNever service your  rearm or your TWM when mounted on a  rearm without

 rst activating the weapon’s safety (if applicable), removing the magazine,

opening the action and physically and visually inspecting to make sure that no

ammunition is installed in the  rearm.

BEFORE ATTACHING, INSPECTING OR SERVICING THE TWM

yEngage the safety on the  rearm (if applicable).

yRemove the magazine from the  rearm (if applicable).

yOpen the action and visually and physically inspect the chamber to be sure it

is empty.

yKeep the barrel pointed in a safe direction at all times and never place your

hand in front of the muzzle.

Produktspezifikationen