Sweex MO251V2 Bedienungsanleitung

Sweex Router MO251V2

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sweex MO251V2 (18 Seiten) in der Kategorie Router. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/18

English version

MO251 / MO251UK Sweex Wireless ADSL 2/2+ Modem/Router 54 Mbps Annex A

Introduction

• Do not expose the Sweex Wireless ADSL 2/2+ Modem/Router 54 Mbps Annex A to extreme temperatures. Do not place the device in direct

sunlight or in the direct vicinity of heating elements.

• Do not use the Sweex Wireless ADSL 2/2+ Modem/Router 54 Mbps Annex A in extremely dusty or moist surroundings.

• Protect the device against powerful shocks or jolts – they may damage the internal electronics.

• Never attempt to open the device yourself – it will cause the warranty to lapse.

Front or top view of the modem

LED indicators Status Meaning

PWR Lit Indicates that the modem is switched on.

1-4 Lit Indicates that a computer is connected to the relevant port.

1-4 Blinking Indicates activity between the relevant computer and the modem.

WL / ACT Lit Indicates that the wireless modem connection is enabled.

WL / ACT Blinking Indicates activity between the wireless computer(s) and the modem.

ADSL Lit The connection with the ADSL line is ok.

ADSL Regular blinking The modem is busy setting up a proper connection or no ADSL is connected to the RJ11

port.

ADSL Lit and blinking fast Indicates activity between the computer(s) and the Internet.

PPP Lit Indicates the use of a PPP connection.

English version

Rear view of the modem

Starting on the left, the following connections can be found at the rear of the modem:

• ADSL port for connecting the ADSL line with telephone cable RJ11.

• UTP Ethernet ports 1, 2, 3 and 4 for connecting computers with an Ethernet network cable RJ45.

• Power port for connecting the power adaptor.

• Antenna connector type SMA

Side view

The Reset button is located on the side of the modem. Use a thin item to press the button. Press and hold the button for 15 seconds. Note! After

this, all settings which apply to your connection and network need to be reconfigured.

The splitter

In order to separate the ADSL signal from the normal telephone signal, you need to use a splitter. This enables you to simultaneously make calls and

surf the Internet using the same telephone line. The signal comes from the wall socket or the meter cupboard and enters the splitter. Two telephone

cables are connected to the output of the splitter. One leads to the modem and the other to the telephone.

Note! The ADSL modem does not include a splitter. It can be obtained from various DIY stores.

Connecting the Sweex ADSL 2 Modem

1. Connect the power adaptor (included) to the rear of the modem and the mains socket. The LED under PWR is lit. In the event the LED is not lit,

check the connections of the power adaptor to the ADSL modem and the mains socket.

2. Connect the telephone cable (RJ11) carrying the ADSL signal to the ADSL port at the rear of the modem. The LED under ADSL will now start to

blink. After approximately 30 seconds the LED will be lit continuously. In the event the LED is not lit, check whether the splitter is properly

connected and/or whether the ADSL line is ok.

3. Switch on the computer and connect it to the rear of the modem using a network cable (UTP RJ45). You can select any of the ports 1, 2, 3 and

4. The corresponding LED at the front of the modem will be lit. In the event the LED fails to light up, check whether the network cable is properly

connected to the computer and the modem.

English version

Configuring the computer to connect to the modem

Windows Vista

In the bottom left of your screen, go to “Start” (Start) “Control Panel” (Control Panel).

Click on “View network status and tasks” (View network status and tasks).

Left in the column, click on “Manage network connections” (Manage network connections).

Produktspezifikationen

Marke:	Sweex
Kategorie:	Router
Modell:	MO251V2
Produktfarbe:	Schwarz
Netzstandard:	IEEE 802.11b, IEEE 802.11g, IEEE 802.3, IEEE 802.3u
Unterstützte Netzwerkprotokolle:	PPTP, PPPoE, Static IP, DHCP Client
Mitgelieferte Software:	Panda Anti-Virus (trial)
Firewall:	Ja
Datenübertragungsgeschwindigkeit WLAN:	54 Mbit/s
xDSL-Verbindung:	Ja
ADSL Spezifikation:	ADSL, ADSL 2, ADSL 2+
ADSL:	Ja
Weitere Anschlüsse:	4x 10/100 LAN\n1x RJ11
Datenübertragungsrate:	100 Mbit/s
Max. Datenübertragungsrate:	0.14 Gbit/s
Datenrate:	WLAN: 1 - 140 Mbps
Netzwerkfunktionen:	Fast Ethernet, Wireless LAN
ISDN Anschluss:	Ja
Aufwärts gerichtete Datenrate:	1 Mbit/s
Abwärts gerichtete Datenrate:	24 Mbit/s