Kuzco Osorio WV347104 Bedienungsanleitung

Lies die bedienungsanleitung für Kuzco Osorio WV347104 (1 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 9 Bewertungen. Hast du eine Frage zu Kuzco Osorio WV347104 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

ALSSEMBY TRUONINSCTIS

WD CAISARNINGANS UTON

• Make sure POWER is at the fuse boxCOMPLETELY OFF

• Have your fixture installed by a qualified licensed electrician

• Prepare everything in a clear area

• Wear gloves at all times during this installation

• Read instructions carefully before you start assembly

• Keep this installation sheet for future reference

WV347104

TEHNICCRTAL SUPPO

1.855.855.8926

ticsualora.comechnalpport@litighng

NOTICE

•afeansctinedn htor The importnt sagurds and itruonouts li ithis see cannot cve

all ssis cce pobitiatile condons a sindtuonthato may urt st b. Imuundtooersd

thutonndrttormufoThtruonat cai a ceaie acnr cafs st be llwe. odese insctis are

proforourndghomndthtrvided y say afet we hily ecrme atnd a licese, ained

eleciciaall is trnnst ithunit.

•fded bed tnstdtaa d This ixture is esigntoe mounton a correcly ialle sndrdroun

orgonbothroughngbothfrThbomu octa x OR a wiri x wi a plaster ame. e x st be

sece e il. sswaurely me sounted tothtructurofth budingThe crobar ha andrdre

sdld buddirti f t may upplie shoue se, ecly mountngthe ixe turtothoute lebox

make i imtpossible ectoorr c

t fe.ly alignthe ixtur

Wall Lamp

CANADA:

USA: 3035 E. Lone Mountain Rd - Las Vegas, NV, 89081

wwligtingcowlora.ah.m

20230619

P:

1.855.855.8926

19054 28th Avenue Surrey - BC V3Z 6M3

ALSSEMBY TRUONINSCTIS

Step 1

Remove fixture from its original package.

Step 2

Separate mounting plate (1c) from canopy (2a) by removing canopy screws

(2b).

Step 3

Attach mounting plate (1c) to electrical junction box (1a) using junction box

screws provided (1e) in hardware package.

Step 4

Make proper electrical connections ( to to “N”, blackhot white“L”, neutral

ground GNDto “”) with wire nuts provided in hardware package and (1b)

place driver (4a) in canopy (2a).

Step 5

Secure filament (5c) to fixture (5b) by threading clockwise. Attach filament

end (5d) to filament (5c) with end cap (5e). Align holes on fixture (5b) and

filament end (5d) with holes on shade (6b), secure with screws (6a).

Step 6

Secure canopy (2a) to mounting plate (1c) with canopy screws (2b).

Step 7

Use dimmer switch (3a) to turn on/off.

Step 8

Use lock (5a) to unlock fixture to adjust tilt and lock in place.

You are now ready to enjoy your fixture.

1a.1b.1c.

4a.2b.3a.

1e.2a.

5a.5b.5c.5d.5e.

6a.6b.

Please Note:

•This Alora LED fixture comes with pre-wired LED module(s)

•Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with

the module could cause permanent damage

•For dimming, an ELV (Electronic Low Voltage) or TRIAC type of dimmer is required

• 120V input

Produktspezifikationen