WyreStorm EX-100-H2 Bedienungsanleitung

WyreStorm Audio-/Video-Extender EX-100-H2

Lies die bedienungsanleitung für WyreStorm EX-100-H2 (4 Seiten) kostenlos online; sie gehört zur Kategorie Audio-/Video-Extender. Dieses Handbuch wurde von 42 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 21.5 Bewertungen. Hast du eine Frage zu WyreStorm EX-100-H2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/4

4K/60 4:2:0 HDR Extender with

USB 2.0, Audio Passthrough & PoH

EX-100-H2 Quickstart Guide

EX-100-H2 Quickstart Guide | 210806

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

Basic Wiring Diagram

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document

versions, additional documentation, and conguration tools.

• Read through the section for important wiring Wiring and Connections

guidelines before creating or choosing premade cables.

• While this product supports CEC, WyreStorm cannot guarantee

compatibility with all forms of CEC communication.

In the Box

1x EX-100-H2 Transmitter

1x EX-100-H2 Receiver

1x 12V DC 2A Power Supply (US/UK/EU/AU)

4x Mounting Brackets with screws

2x 3-pin Terminal Blocks

1x QuickStart Guide (this document)

KEY

HDMI

Control

Power

Ethernet/HDBaseT

Analog Audio

USB

Wireless Router

Control System Transmitter Receiver

Personal

Computer

USB

Camera

Keyboard and Mouse

Headphones

Display Device

EX-100-H2 Quickstart Guide | 210806

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

Audio Connections

Tip:

Ring:

Left Channel

Right Channel

Sleeve: Ground (GND)

RS-232 Wiring

The EX-100-H2 uses a 3-pin RS-232 with no hardware flow control. Most

control systems and computers are DTE where pin 2 is RX, this can vary from

device to device. Refer to the documentation for the connected device for pin

functionally to ensure that the correct connections can be made.

Refer to for details on setting RS-232 modes.RS-232 Mode Settings

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit)--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends the use of shielded category cable to minimize

signal noise and interference.

• WyreStorm recommends using pre-terminated HDMI cables due to the

complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

EX-100-H2 Quickstart Guide | 210806

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiver.

• Verify that the HDBaseT cable is properly terminated following EIA568B

standard.

• Verify that the output resolution of the source and display is supported by

this extender.

• If transmitting 4K, verify that the HDMI cables used are 4K rated.

• Verify that all source and HDBaseT connections are not loose and are

functioning properly

No or Intermittent 3rd party Device Control

• Verify that the IR and RS-232 cables are properly terminated following the

Wiring and Connections section.

• Verify that RS-232 modes are properly selected for the desired operation.

Refer to for details.RS-232 Mode Settings

Troubleshooting Tips:

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

Warranty Information

WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a

period of ve (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited

product warranty.

Produktspezifikationen

Marke:	WyreStorm
Kategorie:	Audio-/Video-Extender
Modell:	EX-100-H2
Unterstützte Audioformate:	LPCM, PCM
Breite:	250 mm
Tiefe:	90.2 mm
Gewicht:	900 g
Produktfarbe:	Schwarz
Übertragungstechnik:	Kabelgebunden
Höhe:	21 mm
Betriebstemperatur:	0 - 45 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 90 %
Schnellstartübersicht:	Ja
Zertifizierung:	FCC, RCM, EAC
Typ:	AV-Sender & -Empfänger
Stromverbrauch (max.):	12 W
Menge pro Packung:	1 Stück(e)
LED-Anzeigen:	Ja
Temperaturbereich bei Lagerung:	-20 - 70 °C
Luftfeuchtigkeit bei Lagerung:	10 - 90 %
Audio-System:	Multikanal
HDCP:	Ja
Unterstützte Video-Modi:	1080p, 2160p
Unterstützte Grafik-Auflösungen:	1920 x 1080 (HD 1080), 3840 x 2160
Rack-Einbau:	Ja
USB-Stecker:	USB Type-A, USB Type-B
Maximale Bildwiederholrate:	60 Hz
Maximale Auflösung:	3840 x 2160 Pixel
Nachhaltigkeitszertifikate:	CE, RoHS
Eingangsstrom:	2 A
Anzahl der HDMI-Ausgänge:	1
Maximal mögliche Übertragungsstrecke:	100 m
Arbeitsspannung:	12 V
unterstütze Kabeltypen:	Cat6, Cat6a, Cat7, HDMI
Bandbreite:	10.2 Gbit/s
HDMI-In:	1
Farbtiefe:	12 Bit
HDCP-Version:	2.2
3,5 mm (1/8-inch) in:	Ja
RS-232 Eingangs-Ports:	1
HDBaseT-Port:	Ja
3,5 mm (1/8-inch) out:	Ja
Erweiterte Display-Identifikationsdaten (EDID):	Ja
Ethernet/LAN:	Ja
CEC-Durchführung:	Ja